You can use the Rola Haul-Your-Might T3 Truck Bed Ladder Rack - Aluminum - 800 lbs item # 59799 with both your truck tool boxes on your 2014 Toyota Tacoma. It will not interfere with your side tool box. You will have to mount your truck box either in front of the ladder rack or behind it. You can not mount your truck box on top of the front legs. view full answer...
On the output post of your dual alternators you will need to run a thick gauge wire from there to the positive post of the batteries you plan on installing in the tool box of your truck. This will put a decent charge on those batteries while you are driving.
To prevent the batteries from discharging your truck batteries you will also need to install the # PK5231201 isolator on this charge line. This will prevent the circuit from the battery of your truck to the battery in your tool box... view full answer...
For your 2012 Ford F-Series Super Duty with a long bed we have a tonneau cover that is specifically designed for fitting behind a tool box with the Access Toolbox Edition Cover part # 834532008460 which will fit and work well as long as your tool box width is between 19 and 21 inches in width. The Truxedo you referenced only fits the short bed versions of your truck so I can not recommend it for your long bed truck. view full answer...
Yes, I spoke with my contact at Thule and they informed me that the Thule TracRac Side-Mount Truck Bed Ladder Rack # TH14750 that you referenced could be installed in the bed of your truck that has a tool box currently installed in it. You would just have to install the rack directly behind the tool box. view full answer...
The Weather Guard Truck Tool Box part # WG45EV is designed to mount in front of the wheel well on the driver side of the truck bed. view full answer...
I do have a truck bed tool box designed to work with the BAKFlip MX4 Hard Tonneau Cover part # BAK48120 for your 2017 GMC Sierra 1500 but the TruXedo TonneauMate Truck Bed Toolbox part # TX1117416 will not work as it is only designed to be used with TruXedo tonneau covers not BAKFlip tonneau covers.
For a toolbox that is confirmed to work with your BAKFlip MX4 Hard Tonneau Cover, I recommend the BAKBox 2 Collapsible Truck Bed Toolbox part # BAK92120. This toolbox is 10" wide x 10" deep... view full answer...
The UWS Tool Box # UWS01048 does not have any fasterners or mounting hardware included or recommended for use by the manufacturer, and will typically just sit in place. The box just slides into place, but if you wanted you could source your own mounting hardware locally; this would require some drilling into the truck bed, and/or box, but it could be done. Your best bet might just be to add some L shaped brackets to the truck bed to keep it from sliding around. view full answer...
The DeeZee Specialty Series Wheel Well Toolbox with Drawers, # DZ95D, allows you to access your tools when the tail gate is open. This installation is behind your wheel well, but there will be space between this box and the side wall of your truck the dimension of which is based on your specific truck bed. The tool box has a quick release from its mount allowing you to move the toolbox and take it with you on the job, and this feature also allows easy removal to clean behind it as needed.... view full answer...
To be blunt you should definitely not alter the installation in any way of the Turnoverball Install Rails # BWGNRK1016-5W or the B&W Companion # BWRVK3400-5W, or the Companion # BWRVK3770 if you have the OEM pucks in your 2019 GMC Sierra 2500 with a 6-1/2 foot bed.
There may be one option for you since you mentioned 18 inches wide and that is the UWS Truck Bed Toolbox - 5th Wheel Series Chest # UWS01042 (Bright Aluminum) or # UWS01066 (Gloss Black). This box measures 58" long x 18" wide... view full answer...
The UWS Truck Bed Chest # UWS01047 doesn't come with any mounting hardware and doesn't actually have any holes predrilled into it for mounting so it would be a custom job to mount it. That being said you could just drill through the bottom of the box and through the bed of your truck and use some larger washers and bolts to mount it, like you stated.
I do recommend using some gasket maker # LT37467 over the bolts so you don't run the risk of water getting inside of your tool box though. view full answer...
The UWS Truck Bed Tool Chest # UWS01044 does require you to drill and use your own hardware to secure it in your truck bed. The choice of hardware is up to you; you could use screws, nuts and bolts or even u-bolts like # CE15252A if you prefer. Your spray-on liner will not be an issue for installation. Dimensions are shown in the linked diagram.
This USA-made tool chest features 8 cubic feet of internal volume and its corrosion-resistant aluminum construction and foam-reinforced lid mean... view full answer...
The B&W Companion # BWRVK3500 is a fixed hitch and for your 2009 Chevrolet 2500 with a 6-1/2 foot bed you're going to need a sliding hitch to have enough turning clearance.
The sliding Companion is # BWRVK3400-5W which will give you an 12 inches of travel to help you make sharp turns. To determine if this will be enough for you to make sharp turns you can do a little math. You need to take the distance from the center of the hitch's jaw to the cab of your truck and add the 12 inches... view full answer...
The fender well toolboxes like # UWS01624 is typically mounted to the floor of the truck bed by drilling through the bottom of the box and into the floor of the truck bed. I'd recommend using stainless hardware to prevent corrosion and fender washers top and bottom to prevent the hardware from pulling through the truck bed and floor of the toolbox. view full answer...
From the tailgate of your truck, to the edge of the rail closest to your cab, it will measure 56-3/8 inches. As long as you have that measurement and as long as the king pin rides above the tool box, you should not have any problem. view full answer...
The DeeZee Red Label 5th Wheel Toolbox, part # DZ8560WB can be installed to the truck bed or it can just sit on the truck bed with no mounting required. The tool box can go behind the truck cab or at the back end of your truck to accommodate your fifth wheel hitch.
To install the DeeZee Toolbox to the truck bed of your 2008 Chevrolet Silverado you will need to drill four 3/16 inch holes through the bottom of the fifth wheel toolbox into your truck bed. Then, you will use the (4) included... view full answer...
After doing some research, I have found that 2 DeeZee Wheel Well Toolboxes # DZ95D will fit in the bed of your 2012 Ford F-350 Super Crew Long Bed with enough room for 4 foot by 8 foot sheets of plywood with room to spare. The bed width of your truck is 79.9 inches and each toolbox has a width of 8.5 inches for a combined width of 17 inches, so with both toolboxes and the sheets of plywood, you should have approximately 14.9 inches of space remaining in your truck bed.
The drawers of this... view full answer...
You will want to use the Underbed Toolbox Mount Kit # 350998 for installing your Underbody Truck Toolbox # UB1818-48 on the bottom of your flatbed due to the tool box's substantial weight of over 100-lbs. The box includes a lock for it's stainless steel T-handle. view full answer...
I spoke with my contact over at Firestone Industrial and the ECU module of the Air Command F3 Compressor System # F2581 and because the signal that the Air Command F3 could potentially be obstructed and/or weakened by placing it inside of a metal toolbox, this is not the recommended application and likely won't function correctly. They recommend that the ECU module is installed along the vehicle frame since it is designed to stand up to moisture, road chemicals, salt spray, and extreme... view full answer...
A chest type toolbox like the # DZ8556 would be attached to the truck bed using the included sheet metal screws through the bottom of the box into the truck bed itself. Be sure to take care when drilling the holes so as not to damage the fuel tank, brake lines or any other components that might be located under the truck bed.
If you wish, you can use bolts instead of the sheet metal screws for added security. view full answer...
The toolbox in your 1995 Dodge Ram 2500 will not interfere with the handle of the Husky Silver Series 26K Fifth Wheel Hitch, # HT31318-31325. The handle will still remain between the base rails of the hitch and will not extend forward past the front base rail. The forward-most edge of the forward-most base rail will be approximately 57 inches from the rear edge of the truck bed (see photo).
You can measure 57 inches from the rear edge of your pickup bed forward to see if your toolbox... view full answer...
Go To Results